![]() Check to insure that the steam mop is plugged into a working outlet. Shark Steam Mop Not Releasing Steam - In the morning, plug the steam mop in and let it heat up and then steam with it. Shark Steam Mop Not Releasing Steam - If this is a major buildup, put. Web if it is on and still not functioning, try resetting the mop by plugging it into a different outlet. If the steam mop does not produce steam, confirm that there is water in the tank. ![]() Shark S3501n Professional Stam Mop Hard Surface Cleaner If the shark steam mop is still not working, try unplugging it for a few minutes and plugging it back in. Shark S3501n Professional Stam Mop Hard Surface Cleaner - image credit : Web there are a few things you can do to troubleshoot your shark steam mop if it’s not steaming. The filter should also be working properly. If you forget any step you can always look back to the tape and figure out how you did it the first time around.Īlso, follow the instructions given in this article properly and you shouldn’t face much trouble.Shark Steam Mop Not Releasing Steam at Ophelia Dunham blog So, videotaping yourself is always a good idea while you are completing the process. If you are taking apart your Shark navigator lift away for the first time then it might look like an enormous task for you multiple things needed to be kept in mind. Slowly remove all the screws one by one and your motor should come out just fine without facing any sort of trouble. If all the screws are in their place you should find 10 screws in total. To remove the motor from the housing you need to remove all the screws from the base. Step 7: Remove the screws located on the bottom side Also, some screws can be found on the back of the handle holder, remove them too. So all in all there should be six screws that you need to take out. A very good point to be noted here is that a screw stays hidden behind the sticker which contains the words “loss of suction”. Remove all the screws which can be found in the front plate. Step 6: Take out all the screws from the motor housing But this pressure is not so much that you need to use a hammer to get the job done. To get rid of these pins you need to apply a specific amount of pressure alongside a center hole punch. These pins hold the latches in their place. But before that first, you need to get rid of the HEPA filter and the cover in front.Īfter that, you need to lay down your motor housing and push the dowel pins. This process is also not that hard to complete and you can do it very easily. The next step of this process is to move the latches from the sides. If you reached this far without facing any great trouble. Step 5: Taking out the latches from the side Just pull it out gently and it’ll come out very easily. Step 4: Taking apart the motor housing unitĪ very easy and fast way to remove the pipe which kind of looks like an elbow is pulling it in your direction. This only activates the brushbar if the handle is in the right position. There’s also a handle engagement switch located on the side of the circuit board. Because sometimes, the circuit board can also be the reason behind your vacuum cleaner not functioning properly. Removing the circuit board is always a good idea if you are removing your brush motor anyway. Use needle-nose pliers to get this job done. But the older models don’t have this and you can easily live it out.Īfter that is done you’ll then need to remove the circuit board leads which are connected with motor contacts. Usually, the newer models have two additional screws on the side of the motor for safety. And once you remove all the screws successfully you’ll have easy access to the components inside. A special star-shaped security bit is required for the job. One thing should be noted that two of these screws are located below the small front wheel and another two in between the big wheels. Start the process by removing the screws. Otherwise, you won’t be able to reach there. ![]() If you want to reach the brush bar and brush motor you have to take out the base plate first. Those steps are as follows Step 1: Taking out the base plate There are multiple steps you need to follow to open and clean up your shark vacuum properly. How to Take Apart Shark Navigator Lift Away 3.3 Can you wash Shark lift away filters.3.2 How to clean HEPA filter on Shark lift away.3.1 How to clean my Shark navigator lift away.2 Top tips before you start the process.1.7 Step 7: Remove the screws located on the bottom side.1.6 Step 6: Take out all the screws from the motor housing.1.5 Step 5: Taking out the latches from the side.1.4 Step 4: Taking apart the motor housing unit.1.3 Step 3: Taking out the circuit board. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |